Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Keith U.

Pages: [1] 2 3 4
1
Culver General Discussion / Re: New Culver Cadet Owner
« on: April 08, 2020, 08:34:05 PM »
I set fuselage on several layers of padding on a trailer, then strapped it down around motor mount and tail, rode about 150 miles that way.  Wings were in a rack, leading edge down, sorry lost a hard drive early during the rebuild so I don’t have a picture of the trailer full of pieces, looked like Sanford and Sons junk wagon.  Good luck with the rebuild, by the photos it looks complete, that’s half of the battle.

2
Maintenance and Repair / Re: Tailgroup alignment
« on: December 18, 2018, 12:37:24 PM »
Thanks Tim, that sounds reasonable, might fly it another season before I get to it.  I am sure that changing the incidence would fix it.  Nothing is simple about this fix though...

3
Maintenance and Repair / Re: Tailgroup alignment
« on: December 16, 2018, 08:51:13 PM »
Tim,
How did you change the incidence in the wing?  I am left wing heavy and really want to get to fly hands off.  I rigged and fussed with control rigging, its gotta be the incidence, not sure how to proceed.  thanks   Keith

4
Culver General Discussion / Re: Oshkosh ´16
« on: August 05, 2018, 11:09:09 PM »
planning on being there this year, and 2020.

5
Culver General Discussion / Re: Oshkosh ´16
« on: July 28, 2018, 10:49:51 PM »
I met Susan Dusenbury, President of Vintage Airplane Assoc, EAA, she owns a Cadet,  maybe we should plan on a group fly in next year at Airventure.  I think we could draw a lot of attention to this remarkable aircraft.   Put it on your calender for 2019.


6
Culver General Discussion / Re: Oshkosh ´16
« on: July 25, 2018, 08:30:10 PM »
Great show as of Wed. home now, 200 miles, 1hr45min, 7.4 gallons, 4,500 msl

7
Culver General Discussion / Re: Oshkosh ´16
« on: July 22, 2018, 10:31:58 PM »
wilco, eta 7/23 08:00 VAP

8
Culver General Discussion / Re: Oshkosh ´16
« on: July 20, 2018, 11:38:19 AM »
winging my Culver to KOSH 7/23-25, anyone else going?

9
Parts For Sale / Culver V gear motors
« on: May 01, 2018, 07:32:45 PM »
Milton Kingsland sent me an email saying he has several electric gear motors for a Cadet, but I think he might have meant “V”. his #503-263-8787 after 2pm pacific time

10
Parts Wanted / Re: In Search of 2 1/2" Dia.Pulleys for 1/8" Control Cables
« on: April 03, 2018, 02:14:55 PM »
Try Univair, you can check the on line catolog, but I have had better luck calling them when looking for someting difficult. 

11
Culver General Discussion / Re: Announcements
« on: March 31, 2018, 12:52:55 PM »
Check out the April, 2018 EAA Sport Aviation for a photo in completion/restoration.

12
Culver General Discussion / Re: Culver Photos Wanted
« on: January 01, 2018, 02:46:29 PM »
How about a Culver fly in?  Would like to see any and all examples.  We could pick a central spot.  Any interest for May/June?

13
Culver General Discussion / Re: Culver Photos Wanted
« on: December 31, 2017, 05:01:41 PM »
Flown 10 hours since Oct., need to make a heat shroud and plow the runway...

14
Culver General Discussion / Re: Culver Photos Wanted
« on: October 31, 2017, 10:18:45 PM »
not able to post picts for some reason...

15
Culver General Discussion / Re: Culver Photos Wanted
« on: October 19, 2017, 10:02:23 AM »
SN 117 is back in the air,  unable to attach picts for some reason...good first flight since 7 year restoration.  3 hours on it now and getting it dialed in.  Full flight report in a few weeks.

Pages: [1] 2 3 4